How to increase the amount of water that you can store in your raintank #2

avatar

Hi Hive DIY and gardening enthusiasts! Here's another simple DIY project from Ligaya Garden. When you've finished reading the post (and hopefully upvoted it), please feel free to comment with any design changes or other uses that you might try for this project.

A little while back, I started a series of posts about how to increase the amount of water you can store in your raintank. You can find that post here if you missed it.

This one the second in that series and shows a different technique.

Lets' have a look!



Like the previous method, this method raises the level of the overflow before it reaches the overflow pipe that runs to your stormwater. Unlike the previous method though, this one is adjustable and doesn't restrict the outlet at all. It uses three 90 degree bends (one of which you are using already) to create an adjustable dogleg which allows you to set the height of the overflow and, thus, the height of the water stored in your tank.

How to do it-




20220810_152320-01.jpeg



Start by sourcing 2 x 90 degree bends. and two short pieces of pipe to join them. You will already have the the third one connected to your tank and existing overflow pipe.



20220810_152346-01.jpeg



You will need to join the pieces together to make a dogleg like in the picture. Don't use glue for this one because you will be needing to twist things around a little. I've included a third bit of pipe in the pic to show the complete thing. You won't use this because it will be replaced by your overflow pipe.

Fit the assembled pipes to the outlet on the outside of your tank and downpipe as shown.

Twist the new bends so that the (horizontal) joiner in the centre is at the same level as the desired water level in your tank.



20220810_152626-01.jpeg


You can see that you have created a restriction that the outflowing water must climb to before it can flow into your stormwater pipes, this effectively raises the water level in the tank.

Don't set your level too high, though, or the water in the tank will flow out through the inspection hatch and cover on the top of the tank and flood the ground around the tank. You still need the water to be able to flow away.

Capturing and storing as much water as possible whenever we can is the only way we can keep gardens and home food production going. The extra litres saved may not seem like a lot but all of the climate projections point to less rainfall coming in heavier downpours because the warming atmosphere can hold more water and is more reluctant to let it go in small amounts. Because global heating adds a degree of uncertainty to any projections, we may see increased localised rain in some areas but, overall, things will be drier. Saving water will become a necessity.



5tbq4JHXhN.png










}

2bP4pJr4wVimqCWjYimXJe2cnCgnKs3wptdZXs8iWD4.webp

VhEcYhIfkj.png



0
0
0.000
9 comments
avatar

This one's a little more complex, I see, but saves even more than the last one.

0
0
0.000
avatar

Different tanks have different overflow designs so some methods work better than others. This one gives you the most scope.

The final post in the series will be about altering the outlet from the inside of the tank. so I have to get around to removing the top of one of mine before I can take pics. I'm doing a whole lot about water harvesting on our website because its an issue that is becoming more important by the day.

0
0
0.000
avatar

Congratulations @ligayagardener! You have completed the following achievement on the Hive blockchain and have been rewarded with new badge(s):

You received more than 65000 upvotes.
Your next target is to reach 70000 upvotes.

You can view your badges on your board and compare yourself to others in the Ranking
If you no longer want to receive notifications, reply to this comment with the word STOP

Check out the last post from @hivebuzz:

Hivebuzz supports the HiveFest⁷ Travel Reimbursement Fund.
0
0
0.000
avatar

Hmm... Reblogging so I can check this out again later on. Interesting...

0
0
0.000
avatar

Interesting. I guess I'll be able to install it on my tank.

0
0
0.000
avatar

This method is adjustable and doesn't take any cutting or gluing, so if you've got the parts, it's a winner.

0
0
0.000