[ESP-ENG] Mi regadera de plantas HIVE hecho con material reciclable | My HIVE plant watering can made from recyclable material

avatar

Saludos a toda la comunidad HIVE, hoy les quiero mostrar una regadera de plantas, hecha con material reciclable, me tocó revisar el lavandero de mi casa para ver que podía conseguir para elaborar esta práctica regadera, así que comencemos este grandioso procedimiento.

Greetings to all the HIVE community, today I want to show you a plant watering can, made with recyclable material, I had to check the laundry room of my house to see what I could get to make this practical watering can, so let's start this great procedure.

mi regadera para plantas hive hecho con material reciclable.jpg

Diseño sin título.jpg

181569117_485651756081414_519302700136314922_n.jpg

  • Los materiales a utilizar son:
  • Envase reciclable de 5 L.
  • Serrucho.
  • Taladro.
  • Pintura roja.
  • Pincel.
  • Tubo de 2 pulgadas PVC.
  • Tapa de 2 pulgadas.
  • Silicone.
  • Marcador.
  • Metro.
  • The materials to be used are:
  • 5 L recyclable container.
  • Saw.
  • Drill.
  • Red paint.
  • Paintbrush.
  • 2 inch PVC pipe.
  • 2-inch cap.
  • Silicone.
  • Marker.
  • Meter.

Diseño sin título.jpg

Diseño sin título (3).jpg

Diseño sin título (4).jpg

  • Paso 1: Medimos en el tubo 25 cm de largo y procedemos a cortar con el serrucho.
  • Paso 2: Luego con el taladro procedemos a abrir los huecos en la tapa de 2 pulgadas.
  • Paso 3: Introducimos la tapa en el tubo ya cortado y volvemos a cortar el tubo a 26 grados.
  • Step 1: We measure 25 cm in length on the tube and proceed to cut with the handsaw.
  • Step 2: Then with the drill we proceed to open the holes in the 2 inch cap.
  • Step 3: We introduce the cap in the already cut tube and cut the tube again at 26 degrees.

Diseño sin título.jpg

Diseño sin título (5).jpg

Diseño sin título (6).jpg

  • Paso 4: Luego marcamos en el envase la parte donde va introducido el tubo con la tapa que es por donde saldrá el agua.
  • Paso 5: Una vez marcado procedemos a cortar para abrir el hueco e introducimos el tubo y pegamos con el silicone.
  • Paso 6: Por último dibujamos nuestro logo HIVE.
  • Step 4: Then we mark on the container the part where the tube with the cap will be inserted, which is where the water will come out.
  • Step 5: Once marked proceed to cut to open the hole and insert the tube and glue with silicone.
  • Step 6: Finally we draw our HIVE logo.

Diseño sin título.jpg

Aquí tenemos nuestro resultado final.

Here we have our final result.

181751035_980876362722288_5997022765306415950_n.jpg

180195587_521016708903052_2893257356205835118_n.jpg

Diseño sin título.jpg

Todas las fotos son de mi Autoría y editadas en canva.

All photos are of my authorship and edited in canva

Diseño sin título.jpg

Gracias por Visitar mi Blog.png



0
0
0.000
6 comments
avatar

que practica se ve esa regadera y no es complicada... felicidades...

0
0
0.000
avatar

Gracias leomara, si es muy práctica y sencilla.

0
0
0.000
avatar

Congratulations @yannet80! You have completed the following achievement on the Hive blockchain and have been rewarded with new badge(s) :

You received more than 700 upvotes.
Your next target is to reach 800 upvotes.

You can view your badges on your board and compare yourself to others in the Ranking
If you no longer want to receive notifications, reply to this comment with the word STOP

Check out the last post from @hivebuzz:

False-Positive phishing alert reported by antivirus software
Feedback from the May 1st Hive Power Up Day
Support the HiveBuzz project. Vote for our proposal!
0
0
0.000
avatar

Mis felicitaciones por tu idea y sobre todo por saber utilizar un taladro: no es nada fácil y se requiere algo de fuerza en las manos. Mis respetos.

0
0
0.000
avatar

Muchas gracias sindetalles, en estos tiempos las mujeres hacemos de todo un poco.

0
0
0.000